Impact Window Guide







Here Is Your Impact Window Guide
Everything You Wanted to Know About Impact Windows Installed In
Fort Myers, Bonita Springs, Naples, Marco Island, Sanibel Island, Cape Coral, LeHigh Acres and all other nearby locations: (Call 239-304-8281 for Naples and Marco Island. Call 239-947-9296 for Bonita Springs and all other locations.)

Getting Started - 10 Things That Installation of Impact Windows Can Do For You

1.Protect Your Family and Your Property From Catastrophic Losses
2.Provide 24/7 Hurricane Impact Protection
3.Receive Insurance Discount
4.Modernize and Beautify Your Home
5.Reduce Cooling Costs By at Least 25%
6.Reduce Solar Heat Gain By 70%
7.Filter Out 95% Of The Damaging UV Light, Reducing Fading
8.Guard Against Unwanted Intruders
9.Dampen Unwanted Outside Sounds
10.Reduce Storm Danger Of Falling Or Flying Glass

 
Going Further, new windows can dramatically change the look of your home as shown in the before and after pictures of the same window area in the next column. This older home had the original unpainted factory aluminum windows that were very typical of Florida construction 20 to 30 years ago  (Before). Impact-Ready, Inc. removed  these outdated, inefficient  and leaky windows and replaced them with Custom Windows vinyl framed insulated impact windows with the Energy Star rated Low E3 366 coating.

 After                   Before


 

,    Ok, so why is a vinyl framed insulated impact window so much better than the aluminum framed impact window of Olde? The main reason is that it gives you 8 means of protecting your home from hurricane projectiles, hurricane wind pressure, heat and water intrusion.

Custom Windows Insulated Vinyl Window cross section:

 

                                       

      1.  The first means of protection is the 3 inch thick honeycomb extruded vinyl frame. The vinyl itself is long lasting and is impervious to the harsh Florida environment. No maintenance is required down the line. The honeycomb design also provides 16 insulating compartments all around the frame. (more than any other window made) As compared to original construction window frames that are just over 1 inch thick, the vinyl frames provide a lot more rigidity and more material to interface with the opening in the building. We also fasten the window to the building with more fasteners that are many times larger than the original installation.  

       2.  The second is the outside sacrificial glass layer. If the window should get hit with a projectile during a wind event, this glass will break, and the resulting fragments will remain outside and not on the carpet and furniture in your home.

       3.  The third is the triple sputtered layer of silver oxide soft coat Low E (Low E3 366) material on the inside (Surface 2) of the sacrificial glass. The microscopic particles are milled such that they have facets like a gemstone that reflect light. Custom Windows has placed this working component on Surface 2 to minimize heating of the inert        
  4.  Argon gas which is the fourth means of protection.

       5.  The fifth is the desiccant material which is located in the metal frame. (See the cross section drawing at the right.) If moisture should somehow infiltrate the insulated glass assembly, perforations in the metal spacer.

       6. 7. 8.  The sixth, seventh, and eighth layers of protection comprise the impact glass sandwich. The center layer in the sandwich is the PVB or SGP polymer material which is the working material that prevents projectiles from penetrating the home.


                                                                       
                                     Glass cross section for Custom Windows Insulated Impact Windows


Why is the Custom Windows Sacrificial Layer on the Outside?
 

     Some window manufacturers install the single pane of glass facing toward the inside of the home. According to Mike LaFevre, Chief Engineer of Custom Windows and the original designer of the vinyl framed impact window, there are two reasons for putting the sacrificial layer on the outside:


1.  When a window is hit with a projectile, the window will deflect 2 to 3 inches like a trampoline. So, the sacrificial layer is going to break no matter whether it is inside or outside. Custom Windows places it on the outside so that dangerous shards of glass are not scattered all over the inside of the home if the window shatters.


2.  After a window is hit with a projectile, the sacrificial layer shatters. The laminated layer still has to hold on to the window frame to prevent the projectile, wind and water from penetrating through the opening. If the laminated layer is on the inside, it will have more surface adhesion to hold onto the window frame and protect the home. The adhesion is provided by the glass mounting “back bedding” which is either cold based urethane or hot based silicone depending on the design and size of the glass. The home now has the greatest protection possible.  

  
If the laminated glass is on the outside - as with some competitor’s windows, and the glass has been hit causing deflection and the shattering of the inside glass, the only thing holding the laminated glass to the frame is the light gauge aluminum air space framing. There is no longer any adhesive holding on to the glass as is the case with a Custom Window. There is a much lower level of penetration protection.

  
Remember, if a window has been hit, it does not mean that the storm is over. The window assembly still has to withstand hours and even days of pounding from wind pressures.

   
Bottom line – laminated glass as the inside layer gives much better overall mechanical protection than laminated glass as the outside layer.


Where should the Low E Soft Coat Layer to be?

 

      The Soft Coat Low E material is normally placed on either the Number 2 or Number 3 glass surface. Custom Windows puts it on the Number 2 surface because in Florida we are most interested in knocking down the heat as soon as possible when it comes in contact with the window. This arrangement lessens the opportunity for the heat to warm up the Argon gas space.


(In Northern climates, it is best to put the coating on the Number 3 surface because they are more interested in keeping the heat in the building.)







Website Builder